The major crankshaft details of the MAN B&W 5L 16/24 are as follows:

In the case of the MAN B&W 5L 16/24 crankshaft, the crankpin diameter is relatively small at 130.00 mm, with a bearing width of only 56.00 mm. To facilitate onsite crankshaft grinding of the crankpin, RA Power Solutions has designed and developed a dedicated onsite crankshaft grinding machine. This machine can be inserted through the inspection window, allowing grinding to be carried out efficiently.

RA Power Solutions deputed technicians, along with equipment, and the following actions were taken:

i) Excessive ovality of 0.97 mm was observed on crankpin No. 03 of the auxiliary engine. Line marks were also noted.
ii) All other parameters, such as hardness, MPI (for crack detection), and visual inspection, were checked and found to be within limits.

iii) Grinding of crankpin No. 03 was carried out, and the diameter was maintained at 128.50 mm (undersized by 1.50 mm).

Advantages of Engaging RA Power Solutions for Repair of Crankshaft – MAN B&W 5L 16/24

i) As a designer and manufacturer of onsite crankshaft grinding machines, we undertake modifications to the equipment, if required, to ensure the successful repair of the crankshaft.

ii) In this case, since the crankpin diameter is only 130.00 mm and the bearing width is 56.00 mm, we developed equipment capable of both grinding and polishing.

iii) We maintain a stock of bearings for popular engine makes and models, including undersized and special sizes. In this case, the required bearings were carried by our technicians, and the engine was commissioned immediately after the crankshaft repair.

Availability of Undersized Crankpin Bearings in Stock of MAN B&W Engine Model No. 5L 16/24

RA Power Solutions has consistently dedicated itself to delivering exceptional and prompt service. With over 46 years of experience, we have successfully repaired more than 10,000 crankshafts worldwide.

We have been regularly providing our services in South Africa, Nigeria, Cambodia, Tanzania, Brazil, Canada, Australia, Bangladesh, Greece, Haiti, Hong Kong, Indonesia, Kenya, Malaysia, Maldives, Kenya, Kuwait, Madagascar, Mexico, Nigeria, Oman, Philippines, Saint Lucia, Saudi Arabia, Singapore, Spain, Sint Maarten, Sri Lanka, Suriname, Thailand, Togo, United Kingdom, United States, Yemen, Zambia, etc.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post Machining of MAN B&W 5L16/24 Crankshaft appeared first on Crankshaft Grinding Repair.

The non-operation of two auxiliary engines stranded the vessel. Considering the urgency of the situation, RA Power Solutions deputed two technicians along with a specially designed onsite crankshaft grinding machine capable of grinding crankpins with small diameters and narrow widths.

In the case of the MAK 6M20 auxiliary engine, the standard diameter of the crankpin is only 152.00 mm, with a bearing width of 71 mm. The design of our onsite crankshaft grinding machine is such that it can be mounted on the crankpin diameter through the inspection window, and grinding is executed in situ.

The details of the engine are as follows:

Upon arrival on board the vessel, our technicians conducted an initial inspection of all crankpins. They found excessive ovality in all six crankpins of the MAK 6M20 engine.

We have provided a copy of the preliminary dimensional inspection report below.

All other parameters, including hardness, MPI, and deflection, were within acceptable limits. We jointly decided to grind all the crankpins, and RA Power Solutions machined them to a final size of 151.00 mm (1.00 mm undersize) as per the above dimensions.

During the stay of our technicians on board the vessel, the crankshaft of Auxiliary Engine #02 was also inspected. We detected excessive ovality showing the same pattern observed in the crankshaft of Auxiliary Engine 01.

The preliminary dimensional inspection report is provided below:

SIZE OF CR Pins Before Grinding of A/E 02
	A	Aa	C	Cc	B	Bb	Min	STD	Ovality
CR-1	151.73	151.85	151.74	151.84	151.75	151.82	151.73	152.00	0.27 MM
CR-2	151.73	151.85	151.72	151.83	151.70	151.81	151.7	152.00	0.30 MM
CR-3	151.72	151.85	151.71	151.84	151.69	151.83	151.69	152.00	0.31 MM
CR-4	151.75	151.85	151.72	151.84	151.73	151.86	151.72	152.00	0.28 MM
CR-5	151.73	151.84	151.69	151.82	151.70	151.84	151.69	152.00	0.31 MM
CR-6	151.73	151.92	151.72	151.89	151.75	151.84	151.72	152.00	0.28 MM

Our technicians ground this crankshaft and maintained the following dimensions. They successfully commissioned both engines in their presence.

SIZE OF CR Pins After Grinding A/E 02
	A	Aa	C	Cc	B	Bb	Min	Max	Ovality
CR-1	151.00	150.99	150.99	150.98	150.99	151	150.98	151.00	0.02 MM
CR-2	151.00	150.99	150.99	150.98	151.00	150.98	150.98	151.00 0.02 MM	0.02 MM
CR-3	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM
CR-4	151.00	150.99	150.98	150.99	150.99	151.00	150.98	151.00	0.02 MM
CR-5	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM
CR-6	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM

The post MAK 6M20 Crankshaft Repair in Baku, Azerbaijan appeared first on Crankshaft Grinding Repair.

We have developed a revolutionized tooling which has the capabilities to execute the repairs to close tolerances as stipulated in the engine manufacturer’s manual.

Case Study of Repair of MAK-1 8CM32C Engine Crankshaft In Burkina Faso, West Africa

The major details of the crankshaft of the MAK-1 8CM32C Engine are as follows:

i) Due to the repeated failure of bearings, it was decided by the client to get an audit of the crankshaft for all the major parameters. RA Power Solutions deputed two (2) technicians along with the onsite crankshaft grinding machine from New Delhi to Burkina Faso. During the initial inspection, the following was checked and observed.

a) The dimensional inspection of the crankpins was conducted, and excessive ovality was observed in all the crankpins. The readings for all the crankpins are pasted below:

b) As protocol, all the crankpins were checked for hardness by a portable hardness tester and were found within limits.

c) MPI was also undertaken to check the cracks, and no abnormality was observed.

ii) The grinding of all the eight (8) crankpins was executed onsite by our technicians. The first step size and tolerance of 0.02/0.03 MM were maintained.

In Place Machining of Crankshaft of MAK-1 8CM32C Engine

RA Power Solutions has been successfully executing the repair of high-diameter crankshafts up to 700 mm. We also specialize in onsite grinding of small-diameter crankpins with a bearing width of the crankpin as low as 50 mm to execute onsite such types of complex crankshaft repairs onsite. We have developed special-purpose onsite crankshaft machining equipment by which the repairs can be executed. We execute repairs for Marine, industrial, stationary power, and offshore sectors all over the world.

Our technicians are available to travel worldwide on short notice. Additionally, several of our technicians hold valid US visas, enabling them to travel to South America, the Caribbean, and other destinations as needed.

At RA Power Solutions, we provide specialized crankshaft grinding machines, onsite crankshaft grinding repair, insitu crankshaft grinding, Onsite crankshaft grinding machines,  insitu crankshaft grinding machines, crankpin bearings, metal stitching, metal locking, engine block repair, crack repair by metal stitching, cast iron crack repair, crankpin polishing, inspection of crankshaft, crankshaft inspection, rebabbitting bearing, babbitt white metal, engine overhauling, grinding of crankpin, connecting rod, and turbine shaft bearing services worldwide, including South Africa, Singapore, Greece, Dubai, Iraq, Iran, Malaysia, Colombia, and Brazil.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post In Place Crankshaft Machining and Grinding of MAK-1 8CM32C Engine In Burkina Faso , West Africa appeared first on Crankshaft Grinding Repair.

Action Taken By RA Power Solutions For Repair of Crankshaft Yanmar 8N 330L EV

i) Since the vessel was anchored near Panama Port, RA Power Solutions deputed two technicians having a valid US VISA and Seaman book. Both technicians flew to Panama along with onsite crankshaft grinding machine and measuring instruments and boarded the vessel within 48 hours of the client’s first information of the breakdown of crankshaft of Yanmar 8N 330L EV.

The Details of Engine / Crankpin are as following:

ii) RA Power Solutions technicians inspected all the crankpins (8 Nos) to check the taper & ovality, the dimensions of observed are pasted below.

iii) On going through the readings, it was observed that the crankpin number #02 has developed excessive ovality of 0.43 MM, against the tolerance of 260.00 MM + 0.03 MM. This is considered very much on the higher side. All other crankpins also have ovality ranging from 0.09 MM to 0.10 MM, The bearing line marks and rough surface on the crankpin were observed.

iv) As a Protocol, hardness was checked of eight (8 Nos) Crankpins and was observed within limits.

v) Crack detection was also conducted, and no crack was observed on damaged crankpin number #02 and other crankpins.

vi) It was jointly decided to undertake the grinding of crankpin number #02 and polishing the remaining crankpins to remove the bearing line marks and to improve the surface finish.

vii) Although in the crankpin numbers #01,#03,#04,#05,#06,#07, and #08 the ovality was observed on the higher side as 0.10 MM, however, this was accepted under divation.

viii) The Crankpin number #02 was undersized by 1.5 MM, A Final Dimensional Report after grinding and polishing of crankpins of Yanmar 8N 330L EV is pasted below.

ix) In order to assist ship staff, our technicians undertook the dimensional and MPI Inspection of connecting rods available on the vessel, they were observed within limits.

The engine was commissioned during the presence of our technicians on the vessel.

We have been regularly executing on site crankshaft repairs and In Situ crankshaft grinding in Dubai, Fujairah, Qatar, Saudi Arabia, Oman, Iraq, Togo, Malta, Freetown, Egypt, Malaysia, Iran, Indonesia, Vietnam, Jordan, etc.

We have a team of trained technicians available 24/7 hrs and can be deputed on short notice. Some of our technicians also have valid US VISA and can fly to South America, Caribbean countries, etc.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post Onsite Repair of Yanmar 8N 330L EV Crankshaft in Panama appeared first on Crankshaft Grinding Repair.

Considering the serious damage to the Auxiliary Engine MAN B&W 6L 16/24, a team of three (3) technicians was deputed, which consisted of a Senior Metal Stitching Engineer and Two (2) technicians to repair the crankshaft.

The vessel was boarded by our technicians in Pasir Gudang. Following are the main details of the engine:

Inspection of Crankshaft:

1. All the crankpins were inspected dimensionally, and line marks and ovality were observed on all the crankpins. The standard diameter of crankpin was 130.00 MM.
2. All other parameters, like hardness, and crack detection by MPI, were found within limits.
3. On visual inspection of the radius fillet of two (2) crankpins was found damaged.

Inspection of Engine Block

1. The Engine Block window seating area of Unit number #04 (Port Side) was found badly damaged.
2. The Cam Case was also found broken.

Few Photographs of the damaged Cam Case are given below:

Broken Camshaft Area of the Window	Damaged Window cover Sittting Area

Action Taken by RA Power Solutions to Repair of Crankshaft and Engine Block of MAN B&W 6L 16/24

i. Considering the damage, all six (6) crankpins diameter was reduced from 130.00 Mm to 129.50 MM, maintaining the tolerance of 0.02 MM.

A copy of the report indicating the final dimensions is pasted below:

ii. The broken engine block was repaired by Metal Stitching Process. The new pieces of casting were metal stitched as shown in the photographs.

Initial Cut Given in Engine Block Window Area	Fitment of New Casting in Damaged Area
MAN B&W Model No.6L 16/24 during metal lock	Metal locking of broken area of MAN B&W Model No.6L 16/24

iii) The Undersize bearings were also supplied by RA Power Solutions.

iv) The Engine was commissioned in the presence of our technicians and performance was found satisfactory.

Pasting of Casting by Metal Lock Process	Perfect Matching of Casting After Metal Locking

Cam Cover Area Metal Stitched

We have been regularly executing on site crankshaft repairs and In Situ Crankshaft Grinding in Dubai, Fujairah, Qatar, Saudi Arabia, Oman, Iraq, Togo, Malta, Freetown, Egypt, Malaysia, Iran, Indonesia, Vietnam, Jordan, etc.

For more details of the Damaged Engine Block by Metal Stitching Process, Onboard Crankshaft Repair Services, repair of crankshaft onsite, in situ crankshaft grinding and repair of MAN engine, onsite crankshaft grinding repair services, onsite crankshaft grinding and repair please email us at info@rapowersolutions.com or call +91 9582647131, or +91 9810012383.

The post Crankshaft Repair of MAN B&W 6L 16/24 In Malaysia appeared first on Crankshaft Grinding Repair.

We extend crankshaft machining for the engines installed in diesel power plants and on vessels. The onsite crankshaft grinding repair services are provided through our technicians who have experience working with engine manufacturers. All the onsite grinding and machining services extended by RA Power Solutions are guaranteed for satisfactory performance. The technical parameters and tolerance of Crankpin Journal repair are maintained as per the manufacturer’s specifications.

Over 44 Years of Crankshaft Grinding and Polishing Machining Experience

RA Power Solutions has experience of more than forty years in this field of crankshaft grinding and machining on land sites and on board sea-going vessels and off-shore anywhere in the world. We offer onsite grinding and machining of crankshafts having diameters ranging from 30 mm to 700 mm.

We are well known as one of the leading companies in the field of onsite grinding and machining of rotary shafts. Our technicians can travel to any part of the world without any hassle. Onsite crankshaft grinding and machining is getting popular nowadays as it save downtime and prices.

The onsite crankshaft grinding machine is developed by RA Power Solutions and is used for grinding, polishing, and machining of crankpin main journal, crankshaft, intermediate shaft, alternator shaft, and pump shaft onsite. By using this grinding equipment, we can save the shaft by maintaining all the parameters mentioned in the engine’s manual.

We are extending our services all over the world with a guarantee and we are known for our sincerity and low prices.

We’re Here to Help You Grow

We have been regularly executing the repairs in Madagascar, Oman, Qatar, Philippines, Bahrain, Srilanka, Bangladesh, Myanmar, Turkey, Nigeria, Greece, Saudi Arabia, UK, Dubai, Malta, Cyprus, Singapore, Malaysia, Colombia, Indonesia, Hong Kong, Spain, Netherlands, Dubai, Portugal, Estonia, Morocco, Belgium, Vietnam, Canada, Jordan, Libya, Kuwait, Egypt, Morocco, Yemen, Bahrain, Tunisia, Sudan, Oman, Algeria, UAE, Iraq, etc.

The Author of This Blog: In Their Own Words

This blog is written by Mr. Raj Shahani (Managing Director of RA Power Solutions India Pvt. Ltd.). Mr. Shahani is a highly experienced business leader with rich experience of more than 40 years in the field of Power, Heavy, and Shipping industry. He is a Technical Adviser to many shipping and heavy industries across the globe.

Mr. Shahani is one of the most enthusiastic professionals and he has all the brilliance of an exemplary leader. He is an extremely effective coach and mentor of teams and is adept at providing leadership in a global, cross-cultural environment.

For more information regarding polishing crank journals, crankshaft bearing journal grinding, crankshaft journal grinding, and crankshaft grinding main journal, please email us at rajshahani@rapowersolutions.com, or info@rapowersolutions.com, or call us at +91 9582647131 or +91 9810012383.

The post Stop Pay Heavy Charges for Grinding and Polishing of Crankshafts appeared first on Crankshaft Grinding Repair.