The major crankshaft details of the MAN B&W 5L 16/24 are as follows:

In the case of the MAN B&W 5L 16/24 crankshaft, the crankpin diameter is relatively small at 130.00 mm, with a bearing width of only 56.00 mm. To facilitate onsite crankshaft grinding of the crankpin, RA Power Solutions has designed and developed a dedicated onsite crankshaft grinding machine. This machine can be inserted through the inspection window, allowing grinding to be carried out efficiently.

RA Power Solutions deputed technicians, along with equipment, and the following actions were taken:

i) Excessive ovality of 0.97 mm was observed on crankpin No. 03 of the auxiliary engine. Line marks were also noted.
ii) All other parameters, such as hardness, MPI (for crack detection), and visual inspection, were checked and found to be within limits.

iii) Grinding of crankpin No. 03 was carried out, and the diameter was maintained at 128.50 mm (undersized by 1.50 mm).

Advantages of Engaging RA Power Solutions for Repair of Crankshaft – MAN B&W 5L 16/24

i) As a designer and manufacturer of onsite crankshaft grinding machines, we undertake modifications to the equipment, if required, to ensure the successful repair of the crankshaft.

ii) In this case, since the crankpin diameter is only 130.00 mm and the bearing width is 56.00 mm, we developed equipment capable of both grinding and polishing.

iii) We maintain a stock of bearings for popular engine makes and models, including undersized and special sizes. In this case, the required bearings were carried by our technicians, and the engine was commissioned immediately after the crankshaft repair.

Availability of Undersized Crankpin Bearings in Stock of MAN B&W Engine Model No. 5L 16/24

RA Power Solutions has consistently dedicated itself to delivering exceptional and prompt service. With over 46 years of experience, we have successfully repaired more than 10,000 crankshafts worldwide.

We have been regularly providing our services in South Africa, Nigeria, Cambodia, Tanzania, Brazil, Canada, Australia, Bangladesh, Greece, Haiti, Hong Kong, Indonesia, Kenya, Malaysia, Maldives, Kenya, Kuwait, Madagascar, Mexico, Nigeria, Oman, Philippines, Saint Lucia, Saudi Arabia, Singapore, Spain, Sint Maarten, Sri Lanka, Suriname, Thailand, Togo, United Kingdom, United States, Yemen, Zambia, etc.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post Machining of MAN B&W 5L16/24 Crankshaft appeared first on Crankshaft Grinding Repair.

The non-operation of two auxiliary engines stranded the vessel. Considering the urgency of the situation, RA Power Solutions deputed two technicians along with a specially designed onsite crankshaft grinding machine capable of grinding crankpins with small diameters and narrow widths.

In the case of the MAK 6M20 auxiliary engine, the standard diameter of the crankpin is only 152.00 mm, with a bearing width of 71 mm. The design of our onsite crankshaft grinding machine is such that it can be mounted on the crankpin diameter through the inspection window, and grinding is executed in situ.

The details of the engine are as follows:

Upon arrival on board the vessel, our technicians conducted an initial inspection of all crankpins. They found excessive ovality in all six crankpins of the MAK 6M20 engine.

We have provided a copy of the preliminary dimensional inspection report below.

All other parameters, including hardness, MPI, and deflection, were within acceptable limits. We jointly decided to grind all the crankpins, and RA Power Solutions machined them to a final size of 151.00 mm (1.00 mm undersize) as per the above dimensions.

During the stay of our technicians on board the vessel, the crankshaft of Auxiliary Engine #02 was also inspected. We detected excessive ovality showing the same pattern observed in the crankshaft of Auxiliary Engine 01.

The preliminary dimensional inspection report is provided below:

SIZE OF CR Pins Before Grinding of A/E 02
	A	Aa	C	Cc	B	Bb	Min	STD	Ovality
CR-1	151.73	151.85	151.74	151.84	151.75	151.82	151.73	152.00	0.27 MM
CR-2	151.73	151.85	151.72	151.83	151.70	151.81	151.7	152.00	0.30 MM
CR-3	151.72	151.85	151.71	151.84	151.69	151.83	151.69	152.00	0.31 MM
CR-4	151.75	151.85	151.72	151.84	151.73	151.86	151.72	152.00	0.28 MM
CR-5	151.73	151.84	151.69	151.82	151.70	151.84	151.69	152.00	0.31 MM
CR-6	151.73	151.92	151.72	151.89	151.75	151.84	151.72	152.00	0.28 MM

Our technicians ground this crankshaft and maintained the following dimensions. They successfully commissioned both engines in their presence.

SIZE OF CR Pins After Grinding A/E 02
	A	Aa	C	Cc	B	Bb	Min	Max	Ovality
CR-1	151.00	150.99	150.99	150.98	150.99	151	150.98	151.00	0.02 MM
CR-2	151.00	150.99	150.99	150.98	151.00	150.98	150.98	151.00 0.02 MM	0.02 MM
CR-3	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM
CR-4	151.00	150.99	150.98	150.99	150.99	151.00	150.98	151.00	0.02 MM
CR-5	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM
CR-6	151.00	150.99	150.98	150.98	150.99	151.00	150.98	151.00	0.02 MM

The post MAK 6M20 Crankshaft Repair in Baku, Azerbaijan appeared first on Crankshaft Grinding Repair.

We have developed a revolutionized tooling which has the capabilities to execute the repairs to close tolerances as stipulated in the engine manufacturer’s manual.

Case Study of Repair of MAK-1 8CM32C Engine Crankshaft In Burkina Faso, West Africa

The major details of the crankshaft of the MAK-1 8CM32C Engine are as follows:

i) Due to the repeated failure of bearings, it was decided by the client to get an audit of the crankshaft for all the major parameters. RA Power Solutions deputed two (2) technicians along with the onsite crankshaft grinding machine from New Delhi to Burkina Faso. During the initial inspection, the following was checked and observed.

a) The dimensional inspection of the crankpins was conducted, and excessive ovality was observed in all the crankpins. The readings for all the crankpins are pasted below:

b) As protocol, all the crankpins were checked for hardness by a portable hardness tester and were found within limits.

c) MPI was also undertaken to check the cracks, and no abnormality was observed.

ii) The grinding of all the eight (8) crankpins was executed onsite by our technicians. The first step size and tolerance of 0.02/0.03 MM were maintained.

In Place Machining of Crankshaft of MAK-1 8CM32C Engine

RA Power Solutions has been successfully executing the repair of high-diameter crankshafts up to 700 mm. We also specialize in onsite grinding of small-diameter crankpins with a bearing width of the crankpin as low as 50 mm to execute onsite such types of complex crankshaft repairs onsite. We have developed special-purpose onsite crankshaft machining equipment by which the repairs can be executed. We execute repairs for Marine, industrial, stationary power, and offshore sectors all over the world.

Our technicians are available to travel worldwide on short notice. Additionally, several of our technicians hold valid US visas, enabling them to travel to South America, the Caribbean, and other destinations as needed.

At RA Power Solutions, we provide specialized crankshaft grinding machines, onsite crankshaft grinding repair, insitu crankshaft grinding, Onsite crankshaft grinding machines,  insitu crankshaft grinding machines, crankpin bearings, metal stitching, metal locking, engine block repair, crack repair by metal stitching, cast iron crack repair, crankpin polishing, inspection of crankshaft, crankshaft inspection, rebabbitting bearing, babbitt white metal, engine overhauling, grinding of crankpin, connecting rod, and turbine shaft bearing services worldwide, including South Africa, Singapore, Greece, Dubai, Iraq, Iran, Malaysia, Colombia, and Brazil.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post In Place Crankshaft Machining and Grinding of MAK-1 8CM32C Engine In Burkina Faso , West Africa appeared first on Crankshaft Grinding Repair.

We recently completed a successful onsite repair of a BERGEN B32:40L8P engine crankshaft onboard a vessel in Jamaica.

The details of the job are as follows:

Onsite Inspection of Crankshaft – BERGEN B32:40L8P

• Two of our experienced technicians, along with our portable onsite crankshaft grinding equipment, traveled from New Delhi, India, to Jamaica.
• Our equipment is lightweight, compact, and portable, allowing it to be transported as accompanied baggage, which eliminates delays associated with cargo shipment and customs clearance.
• Upon boarding, the vessel was found fully loaded with containers, yet our team immediately initiated the crankshaft inspection.
• It was observed that Crankpin No. 5 had suffered severe damage due to a bearing failure.
• The crankpin was thoroughly cleaned, and embedded bearing material was carefully removed.
• Dimensional checks revealed:
  • Minimum Diameter: 269.75 mm
  • Maximum Diameter: 270.00 mm
  • Ovality: 0.25 mm
  • Deep scoring marks were also noted due to the bearing failure.
• A Magnetic Particle Inspection (MPI) using a high-intensity Magnaflux torch was conducted to check for cracks. No cracks or abnormalities were detected.
• Hardness testing was performed, and confirmed that values remained within permissible limits.

Onsite Grinding of BERGEN Crankpin

• The crankpin was calibrated and ground in multiple stages, with ovality strictly controlled during the process.
• Due to deep scoring, the crankpin had to be ground to an undersize of 2 mm.
• The final dimension achieved was 268.00 mm – 0.02 mm, ensuring precision and compliance with engine requirements.

Engine Commissioning

• The vessel had a 2 mm undersize bearing in stock, which was installed immediately after grinding.
• A trial run of the engine was conducted in the presence of our technicians, and performance was found to be fully satisfactory.

About RA Power Solutions

We are a global leader in onsite crankshaft grinding and repair services for crankpins and main journals up to 700 mm. With over four decades of hands-on experience, we are Asia’s most established and trusted company in this field.

We are the original developers and manufacturers of portable onsite crankshaft grinding machines. Our machine design originates from a reputed Italian engineering firm. To date, we have supplied over 80 onsite crankshaft grinding machines across the globe.

In addition to repair services, we also supply the complete range of tools and measuring instruments necessary for crankshaft repairs.

We offer hands-on training programs for client technicians at our in-house training center in New Delhi, India, conducted by our expert engineers. Our training sessions have been successfully delivered to clients from Colombia, Panama, Ecuador, Dubai, Singapore, Bangladesh, Tanzania, and many other countries.

For more information regarding crankshaft grinding services, Crankshaft Repair, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post Crankshaft Repair | Onsite Crankshaft Grinding | BERGEN Engine | 45 Years Experience appeared first on Crankshaft Grinding Repair.

The Auxiliary engine number #02 of MAN B&W 5L 16/24 was stopped due to low air pressure, two of our technicians boarded the vessel and inspected the crankshaft. All Five (5) crankpins having a standard diameter of 130.00 MM had ovality ranging from 0.10 MM to 0.40 MM, which is considered to be on the higher side. The crankpins also had bearing line marks, rough surfaces, and localized damage, as the engine was operated in spite of the problem in the crankshaft.

The dimensional Report of crankpins is pasted below:

The hardness and MPI for crack detection was conducted and no abnormality was observed. Technicians started onsite grinding of crankpins were ground ranging from 1.0 MM undersize to 1.50 MM.

The main advantage of onsite crankshaft grinding jobs executed by RA Power Solutions is that the technicians and equipment are trained and designed to execute the job even while sailing of the vessel. There was absolutely no requirement of holding of the vessel. RA Power Solutions also supplied the undersized crankpin bearings for this engine and it was commissioned in a short notice.

RA Power Solutions with experience of more than 44 years extends onsite crankshaft grinding services to leading shipping companies, power plants and heavy industries all over the world.

For more information regarding crankshaft grinding services, please contact us at rajshahani@rapowersolutions.com or info@rapowersolutions.com or call us at +91 9582647131 or +91 9810012383.

The post Onsite Crankshaft Grinding Repair of MAN B&W 5L 16/24 appeared first on Crankshaft Grinding Repair.

Due to the ship owner’s commitment, they were unable to hold the vessel at the Fujairah Anchor (Dubai) and wanted the repair of damaged crankpin number four of the MAN B&W 5L 16/24 to be executed while sailing the vessel.

RA Power Solutions deployed two technicians to Fujairah Anchor (Dubai) with a specially designed and compact onsite crankshaft grinding machine. In the case of the MAN B&W 5L 16/24, the standard crankpin diameter is 130 mm, and the bearing length is only 56 mm, which is considered to be very small. RA Power Solutions has designed, developed, and manufactured dedicated crankshaft grinding equipment capable of grinding crankpins without removing the crankshaft from the block.

Inspection of damaged crank pin number four was conducted, and it was observed that the minimum diameter of damaged crankpin number four was as follows.

• The minimum diameter of crankpin number four is observed as 129.39 mm.
• The maximum diameter was observed at 130.00 mm.

Thus, an ovality of 0.61 mm was observed, which is considered to be on the higher side. RA Power Solutions technicians executed the grinding of crankpin number four of MAN B&W 5L 16/24 while sailing from Fujairah Anchor (Dubai) to Galle Port, Sri Lanka. The crankpin number four was undersized by 1 mm, and the final diameter was maintained at 129.00 mm.

Huge Savings of Ship Owners Due to Execution Of Crankshaft Repair Which Sailing of the Ship

The repair of the crankshaft of the MAN B&W 5L 16/24 executed by RA Power Solutions resulted in huge savings for ship owners. We have the equipment, technology, and processes to execute crankshaft repairs while the vessel is sailing, with absolutely no requirement to hold the vessel for crankshaft repair.

The author is Mr. Raj Shahani, Managing Director of the company. He has 44 years of experience in grinding crankshafts, polishing crankshafts, and all services related to engine and supporting equipment repair. He has designed and developed a portable crankshaft grinding machine to save time and money.

We have been regularly providing our services in Canada, Australia, Bangladesh, Canada, Dubai, Greece, Haiti, Hong Kong, Indonesia, Kenya, Malaysia, Maldives, Kenya, Kuwait, Madagascar, Mexico, Nigeria, Oman, Philippines, Saint Lucia, Saudi Arabia, Singapore, Spain, Sint Maarten, Sri Lanka, Suriname, Thailand, Togo, United Kingdom, United States, Yemen, Zambia, etc.

For more details, crankshaft repair on vessel, onsite crankshaft grinding machine, grinding of crankshaft main journal, main journal crankshaft grinding service, crankshaft journal polishing and grinding, main journal polishing and in situ crankshaft grinding please email us at rajshahani@rapowersolutions.com, or info@rapowersolutions.com, or call us at +91 9582647131 or +91 9810012383.

The post MAN B&W 5L 16/24 Crankshaft Repair While Sailing of The Vessel appeared first on Crankshaft Grinding Repair.